良许Linux教程网 干货合集 网络端口地址转换 NAPT配置方法

网络端口地址转换 NAPT配置方法

本篇文章重点为大家讲解一下网络端口地址转换 NAPT 配置方法,有需要的小伙伴可以参考一下。

实验目的

理解 NAT 网络地址转换的原理及功能 掌握 NAPT 的配置,实现局域网访问互联网

实验背景

你是某公司的网络管理员,公司办公网需要接入互联网,公司只向 ISP 申请了一条专线,该专线分配了一个公司 IP 地址,配置实现全公司的主机都能访问外网。

技术原理

NAT 将网络划分为内部网络和外部网络两部分,局域网主机利用 NAT 访问网络时,是将局域网内部的本地地址转换为全局地址(互联网合法的 IP 地址)后转发数据包; NAT 分为两种类型:NAT(网络地址转换)和 NAPT(网络端口地址转换 IP 地址对应一个全局地址)。 NAPT:使用不同的端口来映射多个内网 IP 地址到一个指定的外网 IP 地址,多对一。 NAPT 采用端口多路复用方式。内部网络的所有主机均可共享一个合法外部 IP 地址实现对 Internet 的访问,从而可以最大限度地节约 IP 地址资源。同时,又可隐藏网络内部的所有主机,有效避免来自 Internet 的攻击。因此,目前网络中应用最多的就是端口多路复用方式。

ISP(Internet Service Provider),互联网服务提供商,即向广大用户综合提供互联网接入业务、信息业务和增值业务的电信运营商。ISP是经国家主管部门批准的正式运营企业,享受国家法律保护。

实验步骤

新建 Packet Tracer 拓扑图

网络端口地址转换 NAPT 配置网络端口地址转换 NAPT 配置

(1)R1 为公司出口路由器,其与 ISP 路由器之间通过 V.35 电缆串口连接,DCE 端连接在 R1 上,配置其时钟频率 64000; (2)配置 PC 机、服务器及路由器接口 IP 地址; (3)在各路由器上配置静态路由协议,让 PC 间能相互 Ping 通; (4)在 R1 上配置 NAPT。 (5)在 R1 上定义内外网络接口。 (6)验证主机之间的互通性。

实验设备

PC 2 台;Server-PT 1 台;Switch_2950-24 1 台 Router-PT 2 台;直通线;交叉线;DCE串口线

PC1

192.168.1.2
255.255.255.0
192.168.1.1

PC2

192.168.1.3
255.255.255.0
192.168.1.1

Server

200.1.2.2
255.255.255.0
200.1.2.1

R1

en
conf t
host R1
int fa 0/0
ip address 192.168.1.1 255.255.255.0
no shutdown
int s 2/0
ip address 200.1.1.1 255.255.255.0
no shutdown
clock rate 64000

R2

en
conf t
host R2
int s 2/0
ip address 200.1.1.2 255.255.255.0
no shutdown
int fa 0/0
ip address 200.1.2.1 255.255.255.0
no shutdown

R1

exit
ip route 200.1.2.0 255.255.255.0 200.1.1.2

R2

exit
ip route 192.168.1.0 255.255.255.0 200.1.1.1
end
show ip route

PC1

CMD
ping 200.1.2.2 (success)

Web 浏览器
http://200.1.2.2 (success)

R1

int fa 0/0
ip nat inside
int s 2/0
ip nat outside
exit
access-list 1 permit 192.168.1.0 0.0.0.255
ip nat pool jaking 200.1.1.3 200.1.1.3 netmask 255.255.255.0 #设置名称为jaking的地址池,起始和终止IP都是200.1.1.3
ip nat inside source list 1 pool jaking overload (无 overload 表示多对多,有 overload 表示多对一)
end
show ip nat translations(无结果)

PC1

Web 浏览器
http://200.1.2.2 (success)

R1

show ip nat translations(有 1 个结果)

PC2

Web 浏览器
http://200.1.2.2 (success)

R1

show ip nat translations(有 2 个结果)

实战演练

R1

Continue with configuration dialog? [yes/no]: n


Press RETURN to get started!



Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#host R1
R1(config)#int fa 0/0
R1(config-if)#ip add 192.168.1.1 255.255.255.0
R1(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

R1(config-if)#int s 2/0
R1(config-if)#ip add 200.1.1.1 255.255.255.0
R1(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
R1(config-if)#clock rate 64000
R1(config-if)#

R2

Continue with configuration dialog? [yes/no]: n


Press RETURN to get started!



Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#host R2
R2(config)#int s 2/0
R2(config-if)#ip add 200.1.1.2 255.255.255.0
R2(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up

R2(config-if)#int fa 0/0
R2(config-if)#ip add 200.1.2.1 255.255.255.0
R2(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

R2(config-if)#

R1

R1(config-if)#exit
R1(config)#ip route 200.1.2.0 255.255.255.0 200.1.1.2

R2

R2(config-if)#exit
R2(config)#ip route 192.168.1.0 255.255.255.0 200.1.1.1
R2(config)#end
R2#
%SYS-5-CONFIG_I: Configured from console by console

R2#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
      D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
      N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
      E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
      i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
      * - candidate default, U - per-user static route, o - ODR
      P - periodic downloaded static route

Gateway of last resort is not set

S    192.168.1.0/24 [1/0] via 200.1.1.1
C    200.1.1.0/24 is directly connected, Serial2/0
C    200.1.2.0/24 is directly connected, FastEthernet0/0

PC1

CMD
ping 200.1.2.2 (success)

PC>ipconfig

IP Address......................: 192.168.1.2
Subnet Mask.....................: 255.255.255.0
Default Gateway.................: 192.168.1.1

PC>ping 200.1.2.2

Pinging 200.1.2.2 with 32 bytes of data:

Request timed out.
Reply from 200.1.2.2: bytes=32 time=24ms TTL=126
Reply from 200.1.2.2: bytes=32 time=25ms TTL=126
Reply from 200.1.2.2: bytes=32 time=20ms TTL=126

Ping statistics for 200.1.2.2:
   Packets: Sent = 4, Received = 3, Lost = 1 (25% loss),
Approximate round trip times in milli-seconds:
   Minimum = 20ms, Maximum = 25ms, Average = 23ms

PC>ping 200.1.2.2

Pinging 200.1.2.2 with 32 bytes of data:

Reply from 200.1.2.2: bytes=32 time=25ms TTL=126
Reply from 200.1.2.2: bytes=32 time=20ms TTL=126
Reply from 200.1.2.2: bytes=32 time=23ms TTL=126
Reply from 200.1.2.2: bytes=32 time=25ms TTL=126

Ping statistics for 200.1.2.2:
   Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
   Minimum = 20ms, Maximum = 25ms, Average = 23ms

Web 浏览器 http://200.1.2.2 (success) 网络端口地址转换 NAPT 配置网络端口地址转换 NAPT 配置

PC2

CMD
ping 200.1.2.2 (success)

PC>ipconfig

IP Address......................: 192.168.1.3
Subnet Mask.....................: 255.255.255.0
Default Gateway.................: 192.168.1.1

PC>ping 200.1.2.2

Pinging 200.1.2.2 with 32 bytes of data:

Reply from 200.1.2.2: bytes=32 time=31ms TTL=126
Reply from 200.1.2.2: bytes=32 time=17ms TTL=126
Reply from 200.1.2.2: bytes=32 time=19ms TTL=126
Reply from 200.1.2.2: bytes=32 time=23ms TTL=126

Ping statistics for 200.1.2.2:
   Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
   Minimum = 17ms, Maximum = 31ms, Average = 22ms

Web 浏览器 http://200.1.2.2 (success) 网络端口地址转换 NAPT 配置网络端口地址转换 NAPT 配置

R1

R1(config)#int fa 0/0
R1(config-if)#ip nat inside
R1(config-if)#int s 2/0
R1(config-if)#ip nat outside
R1(config-if)#exit
R1(config)#access-list 1 permit 192.168.1.0 0.0.0.255
R1(config)#ip nat pool jaking 200.1.1.3 200.1.1.3 netmask 255.255.255.0
R1(config)#ip nat inside source list 1 pool jaking overload
R1(config)#end
R1#
%SYS-5-CONFIG_I: Configured from console by console

R1#show ip nat translations
R1#


PC1

Web 浏览器
http://200.1.2.2 (success)

R1
show ip nat translations(有 1 个结果)

R1#show ip nat translations
Pro  Inside global     Inside local       Outside local      Outside global
tcp 200.1.1.3:1026     192.168.1.2:1026   200.1.2.2:80       200.1.2.2:80


PC2

Web 浏览器
http://200.1.2.2 (success)

R1
show ip nat translations(有 2 个结果)

R1#show ip nat translations
Pro  Inside global     Inside local       Outside local      Outside global
tcp 200.1.1.3:1026     192.168.1.2:1026   200.1.2.2:80       200.1.2.2:80
tcp 200.1.1.3:1024     192.168.1.3:1026   200.1.2.2:80       200.1.2.2:80

总结

至此,用思科模拟器进行网络端口地址转换 NAPT 配置完毕。

以上就是良许教程网为各位朋友分享的Linu系统相关内容。想要了解更多Linux相关知识记得关注公众号“良许Linux”,或扫描下方二维码进行关注,更多干货等着你 !

img
本文由 良许Linux教程网 发布,可自由转载、引用,但需署名作者且注明文章出处。如转载至微信公众号,请在文末添加作者公众号二维码。
良许

作者: 良许

良许,世界500强企业Linux开发工程师,公众号【良许Linux】的作者,全网拥有超30W粉丝。个人标签:创业者,CSDN学院讲师,副业达人,流量玩家,摄影爱好者。
上一篇
下一篇

发表评论

联系我们

联系我们

公众号:良许Linux

在线咨询: QQ交谈

邮箱: yychuyu@163.com

关注微信
微信扫一扫关注我们

微信扫一扫关注我们

关注微博
返回顶部